Home News Forum Kijk/Luister Sample Sets Vergelijk Benodigdheden Foto's Links Downloads Over ons

 

aansluiten midi emu 1616M

Toon actieve onderwerpen


Berichten: 183

Geregistreerd: 14 maart 2012 15:39

Bericht 05 jul 2016 23:17

aansluiten midi emu 1616M

Hallo,

Ik werk al enige jaren met een EMU1616m geluidskaart. Omdat deze kaart geen midi-usb-ingang maar een 9-pins seriel heeft, is de midi-interface aangesloten op de pc. Want ik kan geen midi-kabel vinden die op de ser.ingang past. Op zich werkt het goed, maar af en toe zijn er wat problemen. Wie heeft deze kaart ook in gebruik
en hoe is de midi-aansluiting dan gerealiseerd?

Mvg,

Gert W.

Jan

Berichten: 706

Geregistreerd: 21 feb 2011 00:16

Bericht 05 jul 2016 23:36

Re: aansluiten midi emu 1616M

Het is geen seriele (RS232/485/422) verbinding, er is gebruik gemaakt van een connector die normaliter voor seriele verbindingen wordt gebruikt. Google leverde het onderstaande resultaat. Met behulp van deze pinout zou het mogelijk zijn om een kabel te maken van DB9 naar de midi DIN pluggen.


May try the following, found here:
Multimedia Production Forums - View topic - E-MU 1616 Midi Breakout Cable Wiring
EMU 1616M Midi Octopus Pinouts

DB-9 Male, DIN5 Female
1 -- NC
2 -- 1-OUT, PIN-4
3 -- 1-OUT, PIN-5
4 -- 2-OUT, PIN-4
5 -- 2-OUT, PIN-5
6 -- 1-IN, PIN-4
7 -- 1-IN, PIN-5
8 -- 2-IN, PIN-4
9 -- 2-IN, PIN-5

PIN 2 OF 1OUT AND 2OUT CONNECTED TO METAL SHIELD OF DB9 SHELL ( ! )
PIN2 OF 1-IN AND 2-IN NC (NO CONNECTION)

Note that they put the 9-pin cable on there to facilitate a 2-in-2-out MIDI capability. (Otherwise, they would have to had put four large round MIDI sockets on it).
Just prepare your four cables, and do one at a time...DB9 Pin2 to first one (1 out) Pin 4, DB9 Pin3 to the same one (1 out) Pin5, and then connect Pin2 of the same DIN5 to the metal shield of the connector. And then, LABEL each one as you finish!
Then, work your way through the rest of them.
By the way, note the unusual numbering of the pins on the MIDI connector:
this video of a guy controlling a whole bunch of parameters with one
They don't start at one end, and count through to the other 1,2,3,4,5. Note that they only use the middle three pins, and those are 5,2 and 4. Don't confuse those, or it definitely will not work!
I can't verify the correctness of this! Use this at your own risk! This is the only thing I found through a quick search.
If you are ONLY concerned with using one single MIDI in/out, you COULD probably just connect the stuff for MIDI 1, and skip the MIDI 2 stuff. In fact, it may be a good idea to just do one, and see if it will connect successfully to another unit, before continuing, if you did want two.
Make sure you put plenty of strain-relief on that connector, somehow. Obviously, four MIDI cables won't fit inside the hole left for the DB9 cover, so you'll have to figure out a way to cut the jackets up to a certain point, so all the wires will pass through the opening, and provide enough support for the two or four dangling cables to get tugged on without continually breaking off wires at the DB9 connector. I don't know if a small zip-tie to clinch down the wire bundle will fit inside the DB9 shell, to prevent pulling? And then, maybe a few layers of progressively larger heat shrink to take care of the "bending/broken wire" situation that will occur right at the shell opening, without it? The heat shrink could go an inch or so out to meet the jackets of the MIDI cables, and then you'll have to bundle those two or four together for a couple inches, overlapping the heat shrink from the wire bundle.
Let us know if it works?
Kapt.Krunch

Berichten: 183

Geregistreerd: 14 maart 2012 15:39

Bericht 06 jul 2016 13:14

Re: aansluiten midi emu 1616M

Jan,

Dank voor je reactie, maar helaas is zelf een kabel maken niet voor mij weggelegd wat kundigheid betreft.

Op E-bay heb ik wel iets gezien, maar is dat dan wel de juiste kabel?

Heeft het sowieso voordelen om de midi rechtstreeks aan te sluiten op de breakoutbox of is mijn huidige verbinding ook prima?

Mvg,

Gert W.
Avatar gebruiker

Berichten: 1758

Geregistreerd: 22 feb 2011 21:29

Woonplaats: Den Haag

Bericht 06 jul 2016 13:58

Re: aansluiten midi emu 1616M

Voor 14.80 euros heb je een complete usb midi interface bij de Bax shop.
http://www.bax-shop.nl/midi-interface/t ... uctreviews
Een complete interface voor de prijs van een kabel.
Er staan ook nog andere Usb interfaces op maar dit is de goedkoopste.

Groet Jan

Berichten: 183

Geregistreerd: 14 maart 2012 15:39

Bericht 06 jul 2016 17:04

Re: aansluiten midi emu 1616M

Hallo,

Iedereen dank voor het meedenken tot nu toe!

Blijft over mijn vraag:
Maakt het verschil of de midikabel middels usb op de pc is aangesloten of dat hij op de breakoutbox zit, dit ivm met soms wat o.a. opstartproblemen waarbij zo te zien midi in het spel is.

Is er iemand die deze kaart gebruikt en hoe is is ie dan midi aangesloten?

Mvg,

Gert W.
Avatar gebruiker

Berichten: 1758

Geregistreerd: 22 feb 2011 21:29

Woonplaats: Den Haag

Bericht 06 jul 2016 18:24

Re: aansluiten midi emu 1616M

Volgens mij is het gewoon plug en play en hoef je alleen het juiste midi device in Hauptwerk te selecteren en dan kan je spelen.

Groet Jan

Keer terug naar Audio / Geluidskaarten voor Hauptwerk

Wie is er online

Gebruikers op dit forum: Geen geregistreerde gebruikers. en 23 gasten




Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by ST Software for PTF. phpBB.nl Vertaling

 

Copyright (c) 2008 PCorgan.com. All rights reserved. Mail: info@PCorgan.com